Buy Now - Pay Later with Affirm
Learn More
  See all Universal & Repair products

Radium Engineering FCST 3 Surge Tank Pump And 1 Lift Pump Included Walbro F90000262 Gas

$1,309.95 Sale:$1,244.45

Radium Engineering

Model #20-0141-03

In Stock

The FCST uses the tried and true Radium Engineering fuel surge tank system preferred by professional motorsports teams worldwide. The optimized 2.2 litercanister supports 1, 2, or 3 internally mounted surge tank pumps capable of up to 1,350LPH @ 43psi. The fuel pumps inside the surge tank provide the primary fueling to the engine. The "lift pump" mounts next to the surge tank canister and keeps the chamber filled with fuel. The volume of fuel inside the surge tank acts as a buffer to always keep the surge tank pump(s) supplied with fuel. This volume is also maintained by the "return" from the fuel pressure regulator. Excess fuel in the integrated surge tank bleeds out into the fuel cell without the need of an expensive hose and fittings. All of this is done inside the fuel cell with the FCST. The surge tank incorporates a multi-pin high amperage sealed electrical bulkhead connector that has 1 connector for each of the 3 selectable pumps.

All internal wires are gasoline, ethanol, and methanol compliant. Furthermore, the internal tube and hoses are a special fluoroelastomer formulation that is suitable for submersion in all types of fuel. FCST Includes -Radium 20-0146 Fuel Level Sensorr Block-Off Kit -Radium 20-0155 Fuel Cell Mounting Tab Kit -Anodized Aluminum 6x10, 24-Bolt Fill Plate -Anodized Aluminum 2.2 Liter Surge Tank Canister -Anodized Aluminum Lift Pump Mounting Brackets -Anodized Aluminum Surge Tank Pump Mounting Bracket -Anodized Aluminum O-Ring Sealed -6AN Fittings -Anodized Aluminum 3/4 Inch -16 (-8AN) Port Plugs x2 -Submersible Rubber Hose and Tubing for all Pumps -24" External Wiring Harness for Surge Tank Pumps -24" External Wiring Harness for Lift Pump -Standard 6-Bolt 2.18" B.C. Flange, Fill Neck Not Included -8AN Sized Vent Hole, Roll Over Valve Not Included -Stainless Steel Hardware -Installation Instructions Selecting the Fuel Pump Configuration The FCST is available with or without fuel pumps. Radium assumes that the lift pump and the surge tank pumps will be the same brand so the internal wiring connectors for the surge tank pumps and the lift pumps will always be the same. If you are going to use your own pumps or source pumps elsewhere, select the option "Surge Tank Pumps and Lift Pump Not Included" from the drop down. Note that there will be enough components included with this option to use 1, 2, or 3 surge tank pumps. Depending on the setup, some parts will simply not be used. Next, select the type of pumps that will be used so the appropriate internal wiring connectors will be included in the kit. If pumps are needed, the FCST will come preassembled and sock filters will be installed on all fuel pumps. First, select the preferred number of surge tank pumps that will be used from the pull down menu.

The FCST is sold in 1, 2, or 3 surge tank pump configurations with 1 lift pump. Next, select the type of pumps that will be used so the appropriate internal wiring connectors will be included in the kit. Note that the surge tank pump's wiring harness is always configured to use up to 3 pumps even if only 1 surge tank pump is selected. Fittings Explained The anodized green fittings signify the surge tank fuel pump outlets to the engine. These are available in -6AN male only. If only 1 surge tank pump is used, the "PUMP2" and "PUMP3" ports are plugged using the included anodized aluminum port plugs. If 2 surge tank pumps are used, the "PUMP3" port is plugged using the included anodized aluminum port plug. If 3 surge tank pumps are used, the included anodized aluminum port plugs will not be used. The "RETURN" black port fitting is used for low pressure fuel returning from the fuel pressure regulator. This port is tapped with 3/4 Inch-16 threads and a -6AN male fitting is included. However, larger -8AN or -10AN male port adapter fittings can be purchased separately HERE if required. Parts Required FUEL CELL A fuel cell is not included in this kit. However, the fuel cell MUST use a 6x10, 24-bolt fill plate flange. The fuel cell cannot be any shorter than 8 inches. The distance from the top of the fuel cell to the bottom of the lift pump filter (lowest point of the kit) is adjustable (8-11 inches depending on how the lift pump is mounted). If the fuel cell is deeper than 11 inches, use this Radium Fuel Pump Inlet Adapter to relocate the lift pump filter to the bottom of the fuel cell. For the ultimate in fuel starvation protection, the lift pump or pickup filter can be placed into the Radium Collector Box. VENT VALVE The FCST uses a 3/4 Inch (19mm) vent hole. If you dont currently have a roll over protection fitting, this Radium -8AN Vent Valve can be used. FUEL FILLER If you do not currently have a 6-bolt (2.18" B.C.) filler, this Radium Fill Neck is unique in that it can be used for direct filling or remote filling.

Features
  • The "lift pump" mounts next to the surge tank canister and keeps the chamber filled with fuel.
  • This volume is also maintained by the "return" from the fuel pressure regulator.
  • Note that there will be enough components included with this option to use 1, 2, or 3 surge tank pumps.
  • Note that the surge tank pump's wiring harness is always configured to use up to 3 pumps even if only 1 surge tank pump is selected.
  • If 3 surge tank pumps are used, the included anodized aluminum port plugs will not be used.
  • Parts Required FUEL CELL A fuel cell is not included in this kit. However, the fuel cell MUST use a 6x10, 24-bolt fill plate flange.
  • The fuel cell cannot be any shorter than 8 inches.
  • FUEL FILLER If you do not currently have a 6-bolt (2.18" B.C.) filler, this Radium Fill Neck is unique in that it can be used for direct filling or remote filling.
Fitment:
  • Universal
Note:
  • Images are for representation only. Actual product may vary
Proposition 65

/!\ warningWARNING: Cancer and Reproductive Harm

https://www.P65Warnings.ca.gov

Radium Engineering is an aftermarket automotive company located in the Pacific Northwest that designs and produces quality performance products. A team with personal passions for innovation leads Radium towards advancement in the industry.

With thorough research and development utilizing state of the art equipment, Radium designs all products in-house with the goal to enhance the driving experience and solve problems that keep vehicles from reaching their full potential. Extensive testing and evaluation ensures the durability and integrity of Radium products exceed consumer expectations.

Currently, Radium manufactures an expanding collection of motorsport parts and accessories for high performance and racing focusing on thier revolutionary fuel surge tank line. An ever expanding collection of application specific parts are also being created. Please contact Radium for more information.