AWE - Save Up to 15%
  See more parts for your Mitsubishi Evolution

GrimmSpeed Boost Control Solenoid Mitsubishi EVO 8|9 03-07

$129.00

GrimmSpeed

Model #057019

Free Shipping


Shopper Award

The GrimmSpeed Mitsubishi EVO Boost Control Solenoid is designed to work with your factory computer (requires tuning). It will not reduce the life of your factory computer because it is designed to draw the same ammount of power as the factory BCS but flows better and reacts faster. It plugs in and requires no splicing or soldering of resistors. With the included bracket you can bolt it in, plug in the connector, and start tuning for fast boost response, increased boost pressure and free up lots of power. Planning on returning the car to stock? Just reverse installation.

Why run an Electronic BCS over a Manual Boost Controller?

A MBC allows you to run higher than stock boost levels by preventing the wastegate from opening at its rated pressure. It does a great job at this but if boost is available under the MBC setting it will give you that full boost. So for instance, you set your MBC to 18psi because from 3000-6000rpm thats what you want. But then say you get detonation with 18psi when you are at 7000rpm unless you are below 16psi. With a MBC, you do not have this control so you are forced to run 16psi through the entire rev range. With an electronic boost controller you could run 18psi from 3000-6000 and 16psi at 7000rpm because you can tune the boost map in the ECU which will allow you to run the maximum amount of boost at every given rpm. This gives you more power throughout the range and better control. Revolutionizing the EVO boost solenoid market, we have created model specific install brackets that allow you to directly fit our Boost Solenoid into your EVO for a factory fit. No more Zip-tying! We give you the factory fitment you have been waiting for.

Staying with the OEM fitment theme, our Boost Solenoid uses a EVO style wiring harness so you can simply unplug your OEM solenoid and plug ours in. No more cutting the oem wiring and crimping wires together!

Also new to the EVO boost solenoid market, we have used ultra low-profile hose fittings to keep the unit as small and clean as possible. The hose fittings are nickel plated brass so you don t have to worry about them snapping off like the plastic hose fittings!

Features:

  • Get into Boost Much Quicker(Flows 10% more than the competition)
  • Plug and Playinto OEM Harness (no splicing wire like other BCS!)
  • Factory Fitwith clean install
  • Works Safely withFactory EVO ECU(customcoil to match ECU)
  • Nickel Plated Fittings as this isBuilt To Last(not the easily breakable plastic fittings!)
  • Easy to Install and Very Easy to Tune.
  • The OnlyDirect Bolt-IN BCSfor EVO
  • Users can use AN fittings with the solenoid.
  • MAC Valve has completely custom made the valve for us(only MAC valve on the market to be custom made for automotive tuning use).
  • Specifically designed by GrimmSpeed to work safely with the factory EVO ECU (requires tuning) and to reliably handle the vibrations and temperatures of your engine bay!
  • The only direct bolt in design for the EVO. Direct bolt in mounting bracket and hardware included! (specify which model before ordering)
  • Faster response and greater flow than any other valve out there. (by more than 10%!)
  • Nickel plated brass fittings. (unlike the competitors failure prone plastic fittings)
Fitments:
  • Mitsubishi EVO 8|9 2003-2007

Other Part Numbers:
GrimmSpeed #grm057019

Proposition 65

/!\ warningWARNING: Cancer and Reproductive Harm

https://www.P65Warnings.ca.gov

Vehicle Engine Notes
2003-2007
Mitsubishi Evolution

2003-2006
Mitsubishi Lancer

Who is Grimmspeed?

Grimmspeed is an automotive aftermarket company that was founded in 2006 by Justin Grimm. They specialize in creating parts for the exhaust system for various automotive vehicles. Grimm has always had this passion for cars and had always wanted to improve his vehicle’s performance. After numerous trials, he was able to perfect his craft and later on decided to turn it into his career. Today, they have become one of the leading brands when it comes to producing high-performance exhaust systems.

Expanding their Product Offering

The company initially manufactured parts for Subaru. But as the company expanded, they started offering parts for other brands such as Ford, Mitsubishi, Hyundai, and Mazda. They now offer parts such as intercoolers, intake, exhaust, engine pulleys, gaskets, boost controllers, phenolic spacers and so much more.

Continuous Product Development

Grimmspeed never stops in finding ways to produce innovative products and is always on the push to keep their products up to date. With the rapid change in automotive technology, it is a must that their product is able to adapt to this change for it to satisfy the demand of its users. This is the reason why the company has gained the trust of many tuners all around.

Purchase Grimmspeed Product at Vivid Racing

Built by an enthusiast for fellow enthusiasts.

If you want a product that is designed to improve the performance of your vehicle, then Grimmspeed is the brand for you. To know more about Grimmspeed, visit Vivid Racing and check out their list of products that would fit your specific needs.





 



What is the GrimmSpeed Limited Lifetime Warranty Policy?GrimmSpeed-branded products are warrantied to the original owner against manufacturing defects in materials and workmanship for the lifetime of the product.

If a GrimmSpeed-branded product covered by this warranty fails due to a manufacturing defect we will repair the product, without charge, or replace it, at our discretion. Only original, unaltered and unmodified materials and workmanship are covered by this policy and you must provide proof of original purchase to be fully covered. This warranty does not cover damage caused by accidents, improper care/installation, negligence, reasonable/normal wear and tear, or the natural breakdown of colors, coatings and materials over extended time and usage. GrimmSpeed cannot be held liable for any damage to your vehicle and/or its components caused by failures associated with the previous statement. Damage not covered under warranty may be considered for repair for a reasonable rate or a reduced price for a replacement piece (a fee will be charged for return shipping).This warranty is available in the United States and Canada.

This warranty does not cover products sold by GrimmSpeed that are not GrimmSpeed-branded products.

This warranty gives you specific legal rights; you may have other rights, which vary from state to state.

The GrimmSpeed website sells GrimmSpeed-branded discontinued, special make-up, and slightly blemished products at significant discounts as 'factory seconds' products. This warranty does not necessarily cover any products purchased as 'factory seconds'. The GrimmSpeed Warranty Department may repair 'factory seconds' products for a reasonable charge and a fee will be charged for return shipping.

Is normal wear and tear covered?

The GrimmSpeed Limited Lifetime Warranty covers manufacturing defects in materials and workmanship, but it does not cover normal wear and tear over extended time and usage. Wear and tear is damage that naturally and inevitably occurs as a result of normal use. Regardless of how carefully you use, or how well you care for your GrimmSpeed product, like all performance parts it will eventually begin to show age and wear. Common examples of wear and tear that would not be covered under the limited lifetime warranty include denting, abrasions or scratches, color changing from heat in exhaust components and so on, less common examples include flex-section wear and fatigue cracks over an extended period of time.

How do I send my product in for warranty?

The first step is to contact support@grimmspeed.com and let them know of your issues/concerns. From there, a customer service representative will personally work with you to determine the best path forward. For the quickest service, please include your contact information and photos of the failed product along with a copy of your receipt/invoice in your initial email.

Upon request from your customer service representative, your product must be returned directly to The GrimmSpeed Warranty Department at 650 Taft St NE, Suite 300, Minneapolis, MN, 55413. All shipping to Warranty must be pre-paid and insured. GrimmSpeed cannot be liable for lost in-bound packages.

Check out these other great products