$129.00
Model #57019
Free Shipping
The Most Complete EVO BCS Ever Built, Period. Get into Boost Much Quicker (Flows 10 Percent more than the competition) Plug and Play into OEM Harness (no splicing wire like other BCS! )Factory Fit with clean Install
Works Safely with Factory EVO ECU (custom coil to match ECU)Nickel Plated Fittings as this is Built To Last (not the easily breakable plastic fittings! )Easy to Install and Very Easy to TuneThe Only Direct Bolt-IN BCS for EVOThe GrimmSpeed Mitsubishi EVO Boost Control Solenoid is Designed to work with your factory computer (requires tuning).
It will Not Reduce the life of your factory computer because it is Designed to draw the same ammount of power as the factory BCS but flows better and reacts faster. It plugs in and requires no splicing or soldering of resistors. With the Included bracket you can bolt it in, plug in the connector, and start tuning for fast boost response, increased boost pressure and free up lots of power. Planning on returning the car to stock? Just reverse Installation.
Why run an Electronic BCS Over a Manual Boost Controller?A MBC allows you to run higher than stock boost levels by preventing the wastegate from opening at its rated pressure. It does a great job at this but if boost is available under the MBC setting it will give you that full boost. So for instance, you set your MBC to 18psi because from 3000-6000rpm thats what you want.
But then say you get detonation with 18psi when you are at 7000rpm unless you are below 16psi. With a MBC, you do Not have this control so you are forced to run 16psi through the entire rev range.
With an electronic boost controller you could run 18psi from 3000-6000 and 16psi at 7000rpm because you can tune the boost map in the ECU which will allow you to run the maximum amount of boost at every given rpm.
This gives you more power throughout the range and better control. Revolutionizing the EVO boost solenoid market, we have created model specific Install brackets that allow you to directly fit our Boost Solenoid into your EVO for a factory fit. No more Zip-tying!
We give you the factory Fitment you have been waiting for. Staying with the OEM Fitment theme, our Boost Solenoid uses a EVO style wiring harness so you can simply unplug your OEM solenoid and plug ours in.
No more cutting the oem wiring and crimping wires together! Also new to the EVO boost solenoid market, we have used ultra low-profile hose fittings to keep the unit as small and clean as possible.
The hose fittings are nickel plated brass so you don't have to worry about them snapping off like the plastic hose fittings! More Features:Users can use AN fittings with the solenoid. MAC Valve has completely custom made the valve for us(only MAC valve on the market to be custom made for automotive tuning use).
Specifically Designed by GrimmSpeed to work safely with the factory EVO ECU (requires tuning) and to reliably handle the vibrations and temperatures of your engine bay!
The only directbolt in Design for the EVO. Direct bolt in mounting bracket and hardware Included! (specify which model before ordering) Faster response and greater flow than any other valve out there. (by more than 10 Percent! )
Nickel plated brass fittings. (unlike the competitors failure prone plastic fittings)Easy for your shop or tuner to tune! (Engine tune is required! )Tuner's comments on our Boost Solenoid AWD Tuning: The GS 3-port BCS provides rapid boost response while maintaining the ability to make acute adjustments via turbo dynamics. While many other boost control solenoids react to adjustments too fast which can make them difficult to control with as much finesse as the stock bleed system.
This solenoid can make micro-adjustments at the edge of target boost Not only providing better spool, but overall more control. Bullwinkle Tuning: The GrimmSpeed BCS is a compact, well Designed unit. Its Design as a 3-port solenoid provides better boost control then the stock bleed-type style.
Often, this enables a tuner to cut mapped wastegate duty cycles in half. This change in WGDC gives a tuner more granularity when tuning, and can yield much improved boost curves. In addition, the 3-port Design often significantly improves spool. Install Guide Mitsubishi Boost Controller Install Instructions
WARNING: Cancer and Reproductive Harm
Make Vehicle | Model | Submodel | Year | Engine | Notes |
---|---|---|---|---|---|
2003-2007 Mitsubishi Evolution |
Evolution | 2003-2007 |
Grimmspeed is an automotive aftermarket company that was founded in 2006 by Justin Grimm. They specialize in creating parts for the exhaust system for various automotive vehicles. Grimm has always had this passion for cars and had always wanted to improve his vehicle’s performance. After numerous trials, he was able to perfect his craft and later on decided to turn it into his career. Today, they have become one of the leading brands when it comes to producing high-performance exhaust systems.
The company initially manufactured parts for Subaru. But as the company expanded, they started offering parts for other brands such as Ford, Mitsubishi, Hyundai, and Mazda. They now offer parts such as intercoolers, intake, exhaust, engine pulleys, gaskets, boost controllers, phenolic spacers and so much more.
Grimmspeed never stops in finding ways to produce innovative products and is always on the push to keep their products up to date. With the rapid change in automotive technology, it is a must that their product is able to adapt to this change for it to satisfy the demand of its users. This is the reason why the company has gained the trust of many tuners all around.
Built by an enthusiast for fellow enthusiasts.
If you want a product that is designed to improve the performance of your vehicle, then Grimmspeed is the brand for you. To know more about Grimmspeed, visit Vivid Racing and check out their list of products that would fit your specific needs.