.jpeg?q=90&p=thumb&w=200&h=200)
.jpeg?q=90&p=thumb&w=40&h=40)
Brakes 
Driveline 
Electronics 
Handlebars & Controls 
Package Deals 
Wheel Accessories 
Wheels by Vehicle 
Tools and Maintenance 
Universal & Repair 
Vivid Racing Gear 
See more parts for Jeep Wrangler
Select the year of your Jeep Wrangler:
Installing comp corners and stretching the wheelbase on your Jeep YJ and TJ can create clearance issues with a standard rear bumper. We are always looking for solutions to problems like this. The Motobilt Comp Cut Rear Bumper is the answer. This bumper fits flush with the sides of the frame.
How does it work? Often times comp cutting the rear of a Jeep YJ or TJ the rear corner body mounts are removed so the tire will not get into it. When this is done a standard bumper extends out into area where the sheet metal has been removed.
You guessed it, in addition to be a clearance issue for some people it also creates an odd looking setup with the bumper sticking out. The Motobilt Comp Cut Rear bumper stops at the edge of the frame for a clean high clearance installation.
The bumper is laser cut and formed from 3/16 inch high strength steel plate. The bumper has internal gussets to add support to the bumper assembly. The bumper features d-ring mounts for recovery. Like all Motobilt bumpers the d-ring mounts pass through the bumper and are welded on both sides for ultimate strength.
Installing the bumper is easy. After removing the existing rear bumper and rear corner body mounts you can get started. The rear cross member can be left in place. You will need to trim the left and right sides where it extends past the frame. The Motobilt bumper lines up flush to the top of your frame rails and centered from side to side.
It welds into the place at that point. One each end of the bumper you weld to the frame and in the center we recommend welding it to the factory cross member. The bumper ships with two side frame plates that cap the bumper off. After you have weld the bumper to the frame you install the caps.
The side caps weld to the frame and to the bumper. The last step would be polishing the welds around the edge of the bumper. If you can throw down with the welder and make clean welds you may want to leave them and show off a little.
Features:
How does it work? Often times comp cutting the rear of a Jeep YJ or TJ the rear corner body mounts are removed so the tire will not get into it. When this is done a standard bumper extends out into area where the sheet metal has been removed.
You guessed it, in addition to be a clearance issue for some people it also creates an odd looking setup with the bumper sticking out. The Motobilt Comp Cut Rear bumper stops at the edge of the frame for a clean high clearance installation.
The bumper is laser cut and formed from 3/16 inch high strength steel plate. The bumper has internal gussets to add support to the bumper assembly. The bumper features d-ring mounts for recovery. Like all Motobilt bumpers the d-ring mounts pass through the bumper and are welded on both sides for ultimate strength.
Installing the bumper is easy. After removing the existing rear bumper and rear corner body mounts you can get started. The rear cross member can be left in place. You will need to trim the left and right sides where it extends past the frame. The Motobilt bumper lines up flush to the top of your frame rails and centered from side to side.
It welds into the place at that point. One each end of the bumper you weld to the frame and in the center we recommend welding it to the factory cross member. The bumper ships with two side frame plates that cap the bumper off. After you have weld the bumper to the frame you install the caps.
The side caps weld to the frame and to the bumper. The last step would be polishing the welds around the edge of the bumper. If you can throw down with the welder and make clean welds you may want to leave them and show off a little.
Features:
- Competion Cut Corner Weld-On Rear Bumper for YJ-TJ
- Finish: Bare
- Material: Steel
- Hardware Included: No
- Sold As: Each
Proposition 65
⚠ WARNING:
Cancer and Reproductive Harm
https://www.P65Warnings.ca.gov
| Vehicle Make/Model | Year | Trims |
|---|---|---|
| Jeep Wrangler | 1987-1995, 1997 | Base |
| Jeep Wrangler | 1987-1990 | Laredo |
| Jeep Wrangler | 1987-1988, 1997-2006 | Sport |
| Jeep Wrangler | 1988-1992 | Islander |
| Jeep Wrangler | 1988, 1991-1994 | S |
| Jeep Wrangler | 1988-1995, 1997-2004 | Sahara |
| Jeep Wrangler | 1991-1994 | Renegade |
| Jeep Wrangler | 1994-1995, 1997-2006 | SE |
| Jeep Wrangler | 1995 | Rio Grande |
| Jeep Wrangler | 2001 | 60 Aniversario |
| Jeep Wrangler | 2002-2006 | X |
| Jeep Wrangler | 2003-2006 | Rubicon |
| Jeep Wrangler | 2003 | X AT |
| Jeep Wrangler | 2004-2006 | Unlimited |
| Jeep Wrangler | 2005-2006 | Unlimited Rubicon |
| Jeep Wrangler | 2006 | 65th Anniversary Edition |
| Jeep Wrangler | 2006 | X 65 Aniversario |
Motobilt was founded in 2012 by offroading pioneer, Dan DuBose and is located at Ozark, Alabama. The company specializes in creating aftermarket parts for various offroad vehicles and Jeeps. They have consistently provided high-quality products. Hence, they have become the brand of choice by multiple offroaders worldwide.
Proudly made in the USAAll of Motobilt’s products are made in the USA. With more than 40 professionals working in their 85,000 square foot facility, the company is able to maintain and control their high-quality standards and provide their customers with the best value for their money.
Making Use of Advanced TechnologyThe company uses state-of-the-art technology in creating their products such as Laser Cutters, Press brake forming, CNC machines, Tube Benders, MIG and TIG welding machines, and more. They utilize the latest 3D CAD Software to create precise and accurate designs that fit perfectly in the vehicle.
Their products are made out of the best raw materials available in the market. This helps in making their product strong and durable that it can handle the toughest terrain encountered during off-roading.
Purchase Motobilt Products at Vivid RacingIf you want to turn your vehicle into a reliable offroading machine, you need parts designed for the occasion and Motobilt is the brand for you. They offer suspension parts, bumpers, stiffeners, chassis reinforcement parts, billet products, and other offroad accessories. If you want a brand that you can depend on, then you came to the right place. Visit Vivid Racing and check out their list of products that would fit your specific needs.
Check out these other great products
Error: Failed to add product
Please refresh the page and try again.